Sunday, July 17, 2011

19. Toolface : Magnetic Tool Face (MTF) , Gravity Tool Face (GTF) , Tool Face Orientation

The sensors used in steering tools and MWD/LWD tools are solid-state electronic devices known as magnetometers and accelerometers which respond to the earth's magnetic field and gravitational field respectively.
 
Since the magnetometers may be affected by the steel collars and drill pipe, the probe must be seated within non-magnetic collars. The probe slots into the muleshoe key, which is aligned with the scribe line of the bent sub. 

The probe therefore measures the direction in which the scribe line of bent sub is pointing.
 
The orientation of the bent sub can be measured relative to Magnetic North (magnetic toolface) or with respect to the High Side of the hole (gravity toolface). 

If we place a plumb bob at the centre of any section of wellbore, the plumb bob orients itself in the direction of "g", vertically downwards. The direction opposite to the orientation of plumb bob is the high side of the wellbore.

At low inclinations (0-5°) magnetic toolface is used, since the High Side is not well-defined at that stage. Once the angle increases, however, and the hole direction becomes established, the gravity toolface is used (i.e. toolface is reported as a number of degrees to the left or right of High Side). 

The High Side of the hole can be defined by the accelerometers. The High Side is directly opposite to the gravity vector, which is the sum of the three gravitational components measured by the accelerometers.
 
Now, before taking this discussion ahead, you should know what scribe line and  the tool face alignment and orientation  means.

Look at the figure below. It shows an adjustable bent sub which gives us an option to adjust the amount of bent we wish to provide to the motor. It generally ranges between 0 to 3 degrees.


Now to provide a desired bent, we hold the upper and lower ABH (Adjustable Bent Housing) using the tong and by using chain tong on orientation sleeve we coincide the upper and lower angular marking to the desired value.

 
Suppose we desire to provide 2.89 degree initial bent. So after coinciding the two angular marking, what the bent sub looks is like in the figure below :


The line passing through the two coincident angular markings give us bent sub tool face, i.e. the orientation of our bent sub. See figure below :


Now have a look at this figure:
This is how the accelerometer and the magnetometer is arranged in the MWD unit aligned  in same axis (z axis).


Typically, three magnetometers and three accelerometers are used to measure the three components of the gravity vector and the Earth magnetic field vector in the sensor frame.

The voltage outputs from the accelerometers are denoted by Gx, Gy and Gz, corresponding to the three orthogonal axes.

Similarly the magnetometer outputs are Hx, Hy and Hz.

z axis points down the axis of the tool and the y axis is defined as being in line with the toolface.

Now in order to accomplish the directional drilling task, the operator needs to know the orientation of the bent sub. The relationship between the directional sensor and the bent sub is fixed for each bottom hole assembly. From the directional sensor measurement, the directional sensor tool face is known. If the angular difference between the directional sensor reference point and the bent sub is measured on the surface, then the operator can use this measurement and the directional sensor tool face reading to determine the orientation of the bent sub, namely, the bent sub tool face. Such angular difference is sometimes called tool face offset.


In the prior art, the angular difference is determined by the use of a scribe line on the exterior of the instrument housing.

Now our next job is orient our MWD/LWD tool in the direction of bent.

Below is a typical BHA arrangement for a 8 1/2" Hole Section :


After we are done with adjusting the bent sub to a desired angle, we make up the string stabilizer, the float sub, the UBHO sub and 1 (one in number) NMDC (also called Monel). To know more about Stabilizer, Float Sub and UBHO sub refer my blog post : Stabilizer, Float Sub , UBHO Sub. 

Now out job is to lower the MWD tool assembly into the NMDC. 

The MWD tool is run inside the NMDC (Monel).

It gets seated in the mule shoe sub (UBHO Sub) which is at the bottom of NMDC.

The tool face of MWD usually doesnot remain aligned with the toolface of downhole motor.

So as to align the MWD toolface with the toolface of downhole mud motor we practise any one of the following procedure :

1
In this procedure, we get back to the time when we have made up the UBHO sub and the MWD tool has not yet been lowered.
 
The mule shoe sub has an adjustable key.

The sleeve with the key can be rotated.

The set screw is loosened and the key is alligned with the bent of the downhole mud motor.

Once the key is aligned with the bent of the motor, the set screw is tightened.

This keeps the key always aligned with the bend provided to the motor.

Now the orientation of mule shoe is same as that of the motor bend.

The MWD tool is run into the NMDC.

The tool has a mule shoe stinger on it.

The stinger has a slot and the mule shoe sleeve has a key.

When the mule shoe stinger enters the mule shoe sub, it is rotated until it gets lined up with the orientation of the mule shoe sub and the motor.
This happens when the slot of the stinger gets seated in key of the UBHO sub.

Note : The survey tool can easily be manually rotated until the tool is aligned with the key.

Thus now the tool face shown by the MWD tool is also the tool face of the bend of the down hole motor.
UBHO Sub


2
In this procedure, we are at the situation when we have lowered the MWD tool in the NMDC and the stinger's slot has got seated in the UBHO sleeve's key.
 
The scribe line at the mule shoe key indicates the tool face of the MWD tool.
The scribe line at bend of the downhole motor indicates the toolface of the bent of the motor.

Now we check that the two scribe lines (one of the motor and other of the surveying tool i.e. MWD here) are aligned or not.

At present condition, we have the following arrangement hanging fron the elevator from top to bottom: NMDC - UBHO Sub - String Stab - Mud Motor - Bit.
We lower the present made assembly until UBHO Sub is on man height.

At the key of the UBHO sub (i.e. on the scribe line), we make any marking like placing a chalk piece or any pointed visible object which shows us the position of the scribe line/ the UBHO key. Some people tape a laser pointing downwards.

Now we lift the made assembly upwards using elevator until we have our bent sub at the man height.

We apply slip to make the assembly stationary.

Now we look up at our placed marking on the UBHO sub and find its position relative to the bend sub scribe line. (For this, the operator stands closer to the bent sub, looks upward to the made marking and tries to make an imaginary line from the marking to the bent.

If the two scribe lines are aligned, then no issues. We are done with our job.

But, if the two scribe lines are not alligned, then we measure the offset tool face (OTF) between the two scribe lines using the protector, which gives and angular value of the offset.

This offset tool face (OTF) is a correction factor.

Now, the operator must decide whether to add or subtract this angular difference to the directional sensor tool face for purposes of determining the orientation of the bent sub. Obviously, the decision as to whether to add or subtract the angular difference is critical. Operators are trained to follow a procedure to correctly determine whether the angular difference should be input into the surface computer as a positive or negative number to be added to the tool face reading to obtain the bent sub orientation. 

Refer figure below which clearly describes the above procedure : 
  
 Geometrically, we can explain the offset angle as shown in figure below :



CORRECTIONS
Offset Correction aligns accelerometer toolface with toolface of bent sub.
Magnetic Declination correction corrects the magnetometer error.

In the picture below, I have tried to explain how the axis of the accelerometer actually behaves and helps determining the inclination, using the help of a hand made rough model.


INCLINATION
The inclination is the angle measured from vertical to the axis of the Z accelerometer.
The inclination can be determined from the above model and comes out to be :

tan α  = ( Gx2 + Gy2 )1/2 / Gz .


TOOLFACE 

Magnetic Tool Face
It is the direction, in the horizontal plane, the bent sub scribe line is pointing with regard to the north reference (Grid, Mag, or True). 

Magnetic orientation is used when the inclination of the well bore is less than 5°. When the inclination is below this amount, the survey instrument cannot accurately determine the highside of the instrument for orientation purposes. The toolface will be presented in azimuth or quadrant form, referenced to magnetic north. The magnetic toolface reading is whatever magnetic direction the toolface is pointed. 

Gravity Tool Face
It is the angular distance that a bent sub scribe line is turned, about the tool axis, relative to the high side of the hole. 

If the inclination of the well bore is above 5° to 8°, then the gravity toolface can be used. 
The toolface will be referenced to the highside of the survey instrument, no matter what the hole direction of the survey instrument is at the time. 
The toolface will be presented in a number of degrees either right or left of the highside. 

GTF orientation is represented by figure below :

BLOG ENDS

74 comments:

  1. Deepak! this is some REALLY handy information!! Plus I found it when I REALLY REALLY wanted it!
    Thanks a lot!

    ReplyDelete
  2. This comment has been removed by the author.

    ReplyDelete
  3. Hi Abid .. thanks for your feedback. Do visit other posts also. I hope you'll like them too.

    ReplyDelete
  4. Great work Deepak. I echo Abid's sentiments.

    ReplyDelete
  5. This is very helpful..Covering the basics.Thanks

    ReplyDelete
  6. Extremely clear and greatly helpful.

    ReplyDelete
  7. Deepak, I just got a job as Directional Driller with no experience straight out of college. My major was in other branch of engineering. I was constantly lost in my training until I found your blog. Thank you very much for the information. I'm not lost any more thanks to you.

    ReplyDelete
  8. Think this stuff is great. What I really like is how current it is.
    Thanks

    ReplyDelete
  9. Thanks man very helpfull..

    ReplyDelete
  10. man... thanks a lot.. good expalanation and illustraion, really helpful.. thanks again for your help to the humanity :)

    ReplyDelete
  11. so vivid explanation

    ReplyDelete
  12. Good but much easier ways.

    ReplyDelete
  13. You really helped me a lot in understanding the difference between GTF and MTF.

    Thank you!

    ReplyDelete
  14. Deepak,

    This is excelent explanation like I've never seen before. Thanks!!!

    ReplyDelete
  15. Deepak,

    You explained this process better than an "expert" training I had for over a week of classes. Great Job. Handy for QA/QC the DD's on my rig.

    Thanks,
    Jesse Rosenbaum- Well Site Drilling Engineer - Alaska

    ReplyDelete
  16. Deepak i m working as data enginner in mudlogging and now a days am working hard to clear my concept regarding MWD and Directional Drilling, So i googled some data regarding it and found ur Blogspot, i m extremely thankful to you and your work is highly appreciated...

    ReplyDelete
  17. no se mucho ingles pero con estas imagenes me quitaron todas mis dudas y comprendi mejo como se va dirigiendo un pozo de perforacion tengo una mejor idea de como se va dirigiendo un motor de fondo

    ReplyDelete
  18. thank you for all those information
    i want to subscribe but i cant i dont know why?

    ReplyDelete
  19. It's really a nice and helpful piece of info. I am glad that you simply shared this useful info with us. Please keep us up to date like this. Thank you for sharing.
    Also visit my web page ; Read �

    ReplyDelete
  20. I'm gone to inform my little brother, that he should also visit this webpage on regular basis to take updated from most recent news update.
    Also visit my web site ... beautytidbits.com

    ReplyDelete
  21. Good day! I simply want to give you a huge thumbs up
    for the great info you have got right here on this post.
    I am returning to your blog for more soon.

    Here is my blog post :: buying a car with bad credit
    My site :: buying a car with bad credit,buy a car with bad credit,how to buy a car with bad credit,buying a car,buy a car,how to buy a car

    ReplyDelete
  22. When sеeking for a cаг dealership Ohio,
    you muѕt be hunting for the best сar modеl at the best pricеs.
    BMW's new i8 is a true sports car that just happens to also be a plug-in hybrid with great efficiency and a short electric-only range. The new Audi A8 features elegant style, wider lounge and sleek instrument panel.

    Have a look at my weblog Buying a car with bad credit

    ReplyDelete
  23. constantly i used to read smaller articles or reviews that
    as well clear their motive, and that is also happening with this piece of writing which I
    am reading at this place.

    My website: michael kors mens watches

    ReplyDelete
  24. Hey! This post couldn't be written any better! Reading this post reminds me of my old room mate! He always kept talking about this. I will forward this page to him. Fairly certain he will have a good read. Thank you for sharing!

    My weblog ... プラダ トートバッグ

    ReplyDelete
  25. We're a bunch of volunteers and opening a brand new scheme in our community. Your site offered us with valuable information to work on. You have done a formidable job and our entire community will likely be grateful to you.

    Look at my blog ... ロレックスコピー

    ReplyDelete
  26. Do you have any video of that? I'd like to find out more details.

    Visit my webpage - chavasymas.com

    ReplyDelete
  27. Very soon this web site will be famous among all blog users, due
    to it's pleasant content

    Look at my homepage; ロレックスレプリカ

    ReplyDelete
  28. Wow, fantastic blog layout! How long have you been blogging for?
    you make blogging look easy. The overall look of your site
    is magnificent, let alone the content!

    my blog :: debragorinmd.blogspot.hu

    ReplyDelete
  29. Excellent items from you, man. I've take note your stuff prior to and you are just extremely excellent. I actually like what you've acquired right here,
    certainly like what you're stating and the way in which by which you assert it. You make it entertaining and you continue to take care of to keep it smart. I can not wait to read much more from you. That is actually a wonderful website.

    Here is my webpage: シャネル バッグ

    ReplyDelete
  30. I all the time used to read post in news papers but now as I am a
    user of internet so from now I am using net for posts, thanks to web.



    Also visit my webpage シャネルトートバッグ

    ReplyDelete
  31. When I originally commented I clicked the "Notify me when new comments are added" checkbox and now each time a
    comment is added I get several emails with the same comment.
    Is there any way you can remove me from that service?
    Thank you!

    Also visit my web page ... シャネル アウトレット

    ReplyDelete
  32. Hello there! I know this is somewhat off topic
    but I was wondering which blog platform are you using for this
    website? I'm getting sick and tired of Wordpress because I've had problems with hackers and
    I'm looking at alternatives for another platform. I would be fantastic if you could point me in the direction of a good platform.

    Feel free to visit my site ... gucci 財布

    ReplyDelete
  33. I'm really enjoying the design and layout of your website. It's a very easy
    on the eyes which makes it much more enjoyable for me
    to come here and visit more often. Did you hire out a designer to
    create your theme? Fantastic work!

    Stop by my homepage :: miumiuoutletshopx.com

    ReplyDelete
  34. Hi there, just wanted to say, I enjoyed this blog post.
    It was practical. Keep on posting!

    Here is my site: グッチ バッグ

    ReplyDelete
  35. Hi would you mind stating which blog platform you're using? I'm going
    to start my own blog in the near future but I'm having a tough time selecting between BlogEngine/Wordpress/B2evolution and Drupal. The reason I ask is because your design seems different then most blogs and I'm looking for
    something unique. P.S Apologies for getting off-topic but
    I had to ask!

    Also visit my homepage ... グッチ バッグ

    ReplyDelete
  36. certainly like your web-site however you need to check the spelling on several
    of your posts. Many of them are rife with spelling
    problems and I to find it very troublesome to tell the truth then again I'll surely come again again.

    My blog :: プラダ バッグ トート

    ReplyDelete
  37. Greetings from Ohio! I'm bored to tears at work so I decided to check out your blog on my iphone during lunch break. I really like the info you present here and can't wait to take a look when
    I get home. I'm surprised at how fast your blog loaded on my cell phone .. I'm not even using WIFI, just 3G .

    . Anyways, superb site!

    Feel free to surf to my site http://carearpc.uzziel.org

    ReplyDelete
  38. excellent issues altogether, you just won a new reader.
    What could you suggest about your put up that you made some days ago?
    Any certain?

    Also visit my web blog; モンスターケーブル

    ReplyDelete
  39. Pretty nice post. I just stumbled upon your blog and wished to say that I have
    truly enjoyed surfing around your blog posts. After all I will
    be subscribing to your feed and I hope you write again soon!


    Feel free to visit my blog - プラダ

    ReplyDelete
  40. Hello there! I know this is kind of off topic but I was wondering which blog platform
    are you using for this site? I'm getting tired of Wordpress because I've had problems with hackers and I'm looking at alternatives for another platform. I would be great if you could point me in the direction of a good platform.

    Here is my weblog; オークリー サングラス

    ReplyDelete
  41. Keep on working, great job!

    Here is my web page: レイバンメガネ

    ReplyDelete
  42. Everything is very open with a clear clarification of the issues.
    It was truly informative. Your site is extremely helpful.
    Thanks for sharing!

    Here is my web site :: ロレックス時計

    ReplyDelete
  43. Hey there! Would you mind if I share your blog with my zynga
    group? There's a lot of people that I think would really appreciate your content. Please let me know. Cheers

    Feel free to visit my webpage; www.monsterbeatsheadphoneoutletsale.com

    ReplyDelete
  44. I am curious to find out what blog system you have been working with?
    I'm having some minor security issues with my latest site and I'd like to find
    something more safe. Do you have any solutions?

    Also visit my web page: エアジョーダンスニーカー

    ReplyDelete
  45. I think that everything said made a great deal of sense.

    However, think on this, suppose you composed a catchier title?
    I am not saying your content is not good, but what if you added something that grabbed a person's attention? I mean "19. Toolface : Magnetic Tool Face (MTF) , Gravity Tool Face (GTF) , Tool Face Orientation" is a little plain. You should peek at Yahoo's front page and note how they create
    post titles to get viewers to open the links. You might add
    a related video or a related pic or two to get readers interested about everything've got to say. Just my opinion, it could make your posts a little bit more interesting.

    Look into my blog アバクロンビー

    ReplyDelete
  46. What's Taking place i'm new to this, I stumbled upon this I have discovered It
    absolutely helpful and it has aided me out loads.
    I am hoping to contribute & assist other customers like
    its helped me. Great job.

    Feel free to surf to my web-site - アバクロ通販

    ReplyDelete
  47. I drop a leave a response whenever I appreciate a post on a website or if I have
    something to contribute to the conversation. It's a result of the passion displayed in the article I browsed. And after this article "19. Toolface : Magnetic Tool Face (MTF) , Gravity Tool Face (GTF) , Tool Face Orientation". I was moved enough to leave a comment :-) I do have a couple of questions for you if you don't mind.
    Could it be simply me or does it seem like some of the remarks come across as if they are coming from brain dead
    individuals? :-P And, if you are writing at other online sites,
    I'd like to follow you. Could you make a list the complete urls of all your community sites like your Facebook page, twitter feed, or linkedin profile?

    Also visit my web blog :: http://ondjoyetu.blogspot.fr/2006/09/receita-para-fazer-fermento.html

    ReplyDelete
  48. you are really a just right webmaster. The web site loading velocity is incredible.
    It seems that you are doing any distinctive trick.
    Also, The contents are masterwork. you have done a wonderful process on this topic!


    Feel free to visit my web blog - christian louboutin pumps

    ReplyDelete
  49. Hey! Someone in my Facebook group shared this website with us so I came to look it over.
    I'm definitely enjoying the information. I'm bookmarking and will be tweeting this to my followers!
    Wonderful blog and brilliant design and style.


    Look into my page monster beats

    ReplyDelete
  50. I have been surfing online more than 2 hours today,
    yet I never found any interesting article like yours.
    It's pretty worth enough for me. Personally, if all site owners and bloggers made good content as you did, the web will be a lot more useful than ever before.

    my web site - blogspot.com

    ReplyDelete
  51. It's really a nice and useful piece of info. I am satisfied that you shared this helpful info with us. Please keep us informed like this. Thanks for sharing.

    Feel free to visit my site: ロレックスコピー

    ReplyDelete
  52. Have you ever thought about publishing an e-book or guest authoring on other sites?
    I have a blog based on the same topics you discuss and would love to have
    you share some stories/information. I know my subscribers would appreciate
    your work. If you are even remotely interested, feel free to
    shoot me an email.

    My weblog :: シャネル アウトレット

    ReplyDelete
  53. Great site you have here but I was curious about if you knew of any community forums that cover the same
    topics discussed here? I'd really love to be a part of community where I can get comments from other knowledgeable individuals that share the same interest. If you have any recommendations, please let me know. Many thanks!

    my page http://www.2013michaelkorsoutletvip.com/

    ReplyDelete
  54. I just like the valuable info you supply to your articles.
    I will bookmark your blog and take a look at once more right here frequently.
    I'm rather sure I will be told plenty of new stuff proper here! Best of luck for the next!

    Review my blog post Michael Kors Outlet

    ReplyDelete
  55. Gοod day! Do you know if they make аny pluginѕ to asѕіst with Seaгch Engіne Οptimization?
    I'm trying to get my blog to rank for some targeted keywords but I'm not seeing veгу gοоd succeѕs.
    If you knoω of any please share. Thanκѕ!


    Looκ аt mу homepage: kate dircksen

    ReplyDelete
  56. Somebody essentially assist to make seriously articles I'd state. This is the first time I frequented your website page and to this point? I surprised with the analysis you made to create this particular submit incredible. Great task!

    Feel free to surf to my homepage ... cheap polo ralph lauren

    ReplyDelete
  57. Virtually it has fluoride -- which remarkably is a poison and not
    developed for human use. Trust me or not, paper t-shirts
    can participate in a thousand things. Well, here is
    definitely some information pertaining to you!
    Prada was first found in 1913 by the Italian brothers
    Mario and Martino Prada. http://rappelkopf.at/wiki/index.
    php/Index.php

    ReplyDelete
  58. Could do ωіth reаdin some moгe content on thiѕ - anу adѵice covering ωhаt books I might read οr what forums Ι сoulԁ ϳoin?


    mу web blog: best unsecured loans

    ReplyDelete
  59. I've got to get it all done because I won't have the chanсе to do it otheг
    ωise!

    My homepage: best uk loans

    ReplyDelete
  60. It holds a high-resolution multi-touch
    inch screen using a wide viewing incline. Leon
    Levin offers a wide spectrum of colouring materials and combinations.
    . Various types of Nike shoes should help you to enjoy your sports activities.
    Cocchia makes the breast coverage low and focuses on a sporting womanliness.
    http://talentswiki.com/index.php5?title=Benutzer:Sophia430

    my page ... nike air max 1

    ReplyDelete
  61. When someone writes an article he/she maintains the idea of a user in his/her brain that how a user can be aware of it.

    Therefore that's why this article is great. Thanks!

    Feel free to visit my web page :: http://cheapnikeairmaxam.tumblr.com

    ReplyDelete
  62. A motivating discussion is worth comment. I believe that you ought to write more about this issue,
    it might not be a taboo matter but typically people do not speak about such topics.
    To the next! Cheers!!

    my page - cheap nike air max shoes

    ReplyDelete
  63. If you are going for most excellent contents like me, only go to see this website
    all the time because it provides quality contents, thanks

    Look at my web blog :: cheap nike air max bw

    ReplyDelete
  64. I am regular reader, how are you everybody? This article posted at this site is really pleasant.


    Here is my web site - cheap nike air max 2009

    ReplyDelete
  65. Ahaa, its nice discussion regarding this paragraph at this place
    at this weblog, I have read all that, so at this time me also commenting here.


    Also visit my site: cheap nike air max bw

    ReplyDelete
  66. Together with the signatured double C logo, the classical design had been launched finally.
    A borns diaper bag will be handed to a different child.
    Genuine luxury handbags can cost anywhere from several hundred
    dollars up to $1,000. You've got a solitary small sized and also you more robust one foot. http://groovaz.com/ForrestO8

    ReplyDelete
  67. Why people still use to read news papers when in
    this technological globe the whole thing is accessible on net?


    my page ... nike air max on sale

    ReplyDelete
  68. You can modify look of a creator handbag
    with different leather materials. Accept is as true or not, released t-shirts can perform thousand things.
    As you can age teeth can be more brittle and thus susceptible
    to hollows and damage. The material in which is used should be 100% silicon rubber.
    http://www.mongoliaonline.com/user/profile/ulrikefar

    ReplyDelete
  69. Hey! I could have sworn I've been to this site before but after browsing through some of the post I realized it's new to
    me. Anyways, I'm definitely delighted I found it and I'll be book-marking and checking back frequently!


    Also visit my weblog - teichpumpe kaufen

    ReplyDelete
  70. Historical past of the paul smith is identifiable to loud and even attention
    catching apparel, especially for adult males. Steve Morley is in command over the traditional Amer-Italian menu.
    In the same way you need to find a new scent for the particular body.

    With them, there will be going to no need to obtain entangled in secondary tasks
    of the organization. http://redesocial.elessandro.net/index.

    php?do=/profile-66362/info/

    ReplyDelete
  71. Internet surveys which look actually complicated may disappointed potential
    respondents. Read more of my Disney Go Examiner articles or
    sign up when a free membership rate. It should definitely be either long a time
    or too superficial. Today the brand manufactures nearly a lot of stuff from furniture regarding
    Kidrobot toys. http://www.vanimalonline.
    com/profiles/155501

    ReplyDelete
  72. This blog help me a lot, thanks a thousand times for get me learn such a things that I have to face in my new career

    ReplyDelete
  73. Although I have read a whole about Toolface/hoghside terms, BUT, I was always confused in the basics, the classification and how it works. Thank you and god bless please keep it up.

    ReplyDelete